|
Num Posts
Sort Order
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/06/08
07:25 AM
|
|
ok i have a cheap redcat 110 and i just brought a new carb for it i put the carb on and now it idles very high in neutral and when i go to put it in gear it takes off like i'm hittin the throttle no mods it's all stock.the old carb i took off was 19mm and the new one is 24mm can anyone help with this matter THANKS ALOT
|
wolf1
Guru
| Posts: 1069
| Joined: 11/07
Posted: 06/07/08
06:14 AM
|
|
there should be an idle screw located on the side of the carb. in the throttle slider housing.
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/11/08
09:17 AM
|
|
yea i messed with that and now if i have it in gear and don't hold the brake it moves by it self whats causin that? THANKS
|
|
|
wolf1
Guru
| Posts: 1069
| Joined: 11/07
Posted: 06/12/08
03:46 AM
|
|
turn it to the left, or turning the idle down a ***
since the clutch is a centrifugal clutch at the engine spins faster the clutch engages. so with idle up it will engage the clutch early.
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/12/08
04:19 AM
|
|
ok i will try that and let you know what happens THANKS
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/12/08
12:27 PM
|
|
hey another ? should i mess with the needle any? move the e clip up or down THANKS
|
wolf1
Guru
| Posts: 1069
| Joined: 11/07
Posted: 06/12/08
01:46 PM
|
|
no
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/12/08
02:39 PM
|
|
ok......i read also that if u put the throttle tube back in wrong your atv will take off on u is this true and if so how do you know if it's in right?
THANKS BRO U HAVE BEEN A BIG HELP BUT THIS IS GETTING FUSTRATING I'M READY TO RIDE LOL
|
wolf1
Guru
| Posts: 1069
| Joined: 11/07
Posted: 06/12/08
09:35 PM
|
|
yes actually it can.
there is a small pin inside the slide housing.
ad a small groove in the slide.
just make sure the slide is all the way in.
put it back in the top and turn it back and forth slowly until it catches the groove and goes all the the way in to the bottom of the throttle housing.
you'll know it is all the way down when you look into the carburetors intake area (where the air filter hose clamps on) and you can't see the jet needle
if you are close to the chattanooga tennessee area bring it on by and i'll help you get it dialed in.
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/13/08
07:00 AM
|
|
naw bro i live in roanoke va but i will mess around with the slide housing and see what happens and i will keep u posted THANKS
|
KUNFUZION
New User
| Posts: 8
| Joined: 06/08
Posted: 06/19/08
04:00 PM
|
|
ok i was messing around with the carb and noticed that the intake gasket was all torn up could this b my problem because now it wont stay started and if so do u think it is a good idea to use that blue gasket maker junk? THANKS
|